Industry Nine Wanderer Carbon SYSTEM Wheelset
The Industry Nine Wanderer Carbon System wheelset is Industry Nine's bikepacking wheel in its flagship trim: a 27mm internal, 2mm offset Convergence carbon rim laced 32 spokes a side with machined aluminum System spokes to the Hydra2 System hub. Industry Nine lists it at 1659 grams for the pair, 757 front and 902 rear, in 29in.
System means the hub shells and spokes are machined in Asheville, North Carolina, the spokes thread straight into the hub, and both come in seven anodized colors. On a bikepacking wheel that gives you the lightest and stiffest Wanderer, a hub with 870 points of engagement for technical loaded climbing, and, unusually for a System build, a full set of rear axle standards including 135mm and single speed.
The Wanderer Carbon System is for the rider doing multi-day trips on a rigid or hardtail 29er who wants a light, strong, purpose-built wheel and is willing to carry a spare System spoke.
Design and construction
The Wanderer rim is a Convergence carbon bikepacking profile: 21mm deep, 27mm inner width, 32-hole, hookless and tubeless ready, with a 2mm spoke-bed offset that evens out spoke tension between the drive and non-drive sides of a dished rear wheel, which matters when the wheel is carrying a load for days. It is built for durability and compliance under weight. We Are One hand lays the rim in Kamloops, British Columbia, and Industry Nine covers it for life, riding impact damage included.
The hub is the Hydra2 System: 870 points of engagement, 0.41 degrees between clicks, six three-tooth pawls, about 60 percent less coasting drag than the original Hydra, a much thicker axle, and a five-year limited hub warranty. Its straight-pull flanges take Industry Nine's one-piece 7075 aluminum System spokes. The hub is 6-bolt.
Hub and spoke colors are chosen separately on the Wanderer Carbon System from Black, Bronze, Gold, Orange, Purple, Red, and Silver.
Industry Nine's aluminum System spokes
Every Wanderer Carbon wheel is built on Industry Nine's aluminum System spoke, and it is the reason a System build rides and looks the way it does. Each spoke is machined from a solid bar of 7075-T651 aluminum in Industry Nine's own facility in Asheville, North Carolina, as a single straight-pull piece: it threads directly into the Hydra2 System hubshell at one end and carries integrated wrench flats at the rim end, so there is no J-bend and no separate nipple anywhere in the wheel. Those two features are where a conventional steel spoke usually fails, at the work-hardened bend and at the threaded nipple interface, and the System spoke simply does not have them. The Wanderer Carbon is laced 32-hole.
On the Industry Nine Wanderer Carbon System wheelset the aluminum spoke is not a lightweight compromise. Industry Nine gives it a 25 to 30 percent larger cross-sectional area than a comparable steel spoke, which it rates as equal in tensile strength to a 14/15-gauge double-butted steel spoke, and the thread root diameter is larger than the spoke body, so the spoke is strongest exactly where a steel spoke is thinnest. The result is a stiff, direct-feeling wheel that holds tension and tracks precisely. Industry Nine builds System wheels to a target tension of 120 kgf and holds every spoke within 10 percent of that figure.
Because the spokes are anodized rather than painted, they come in the same seven colors as the hubs, and the hub and spoke colors are chosen independently, so a bronze hub with silver spokes or an orange hub with black spokes is a normal order rather than a custom one. The Hub Color and Spoke Color menus on this Industry Nine Wanderer Carbon System page drive exactly that choice and the preview picture follows it. One thing to know before you order: Industry Nine keeps the System spoke in-house and does not sell it over the counter, so a System wheel is serviced and rebuilt through authorized dealers such as ProWheelBuilder, and the spokes are warranted against manufacturing defects. If you would rather have a wheel any shop can re-spoke with stock parts, Industry Nine's Classic and 1/1 builds use the same rims with steel J-bend Sapim spokes and conventional nipples.
How it rides
Loaded, the Wanderer Carbon System feels composed. Thirty-two aluminum spokes and the offset carbon rim make a wheel that stays true under 30 pounds of bags and does not flex when you stand on a steep climb, and the Hydra2 drive picks up instantly on the ratchety, rooty ascents that loaded bikes have to walk up if the hub is slow. The 27mm bed suits 2.1 to 2.4in tires, which is the range most bikepacking rigs run.
It is stiffer than the Classic version, which on a rigid bike is something to think about; some riders on washboard prefer the steel-spoke build. But for the rider who wants the lightest strong wheel for a route with real climbing, the Wanderer Carbon System is the one that will feel best on day four.
The single-speed and 135mm rear options are a quiet strength of this build. Plenty of dedicated bikepacking frames still use 12x142 or quick-release dropouts, and a fair number of riders run single speed for simplicity on long trips; the Wanderer Carbon System covers both without a custom build.
Specifications
| Wheel type | Bikepacking |
|---|---|
| Rim | Wanderer Carbon (Carbon Fiber) |
| Rim depth | 21mm |
| Inner width | 27mm |
| ERD | 600mm with 2mm offset |
| Hole count | 32h |
| Hub platform | Hydra2 System hub, straight-pull System spokes, 870 points of engagement, 0.41 degrees |
| Brake mount | 6 Bolt |
| Hub colors | Black, Bronze, Gold, Orange, Purple, Red, Silver |
| Spoke colors | Black, Bronze, Gold, Orange, Purple, Red, Silver |
| Front axle | 15x110, 15x110 RockShox Torque Cap |
| Rear axle | 10x135, 12x135, 12x142 single speed, 12x148 |
| Freehub | Shimano HG, Shimano Micro Spline, Single Speed, SRAM XD |
| Wheelset weight | 1659g |
| Front / rear weight | 757g / 902g |
| Intended use | Bikepacking |
This listing
This listing is the Wanderer Carbon SYSTEM Wheelset as Industry Nine sells it. The choices on this page are driver type: Shimano HG, Shimano Micro Spline, Single Speed, SRAM XD; axle: Wheelset - 15x110mm F / 10x135mm R, Wheelset - 15x110mm F / 12x135mm R, Wheelset - 15x110mm F / 12x142mm Single Speed R, Wheelset - 15x110mm F / 12x148mm R, Wheelset - 15x110mm RockShox Torque Cap F / 10x135mm R, Wheelset - 15x110mm RockShox Torque Cap F / 12x135mm R, Wheelset - 15x110mm RockShox Torque Cap F / 12x142mm Single Speed R, Wheelset - 15x110mm RockShox Torque Cap F / 12x148mm R; hub color: Black, Bronze, Gold, Orange, Purple, Red, Silver; i9 alloy system spoke color: Black, Bronze, Gold, Orange, Purple, Red, Silver. This listing is the complete wheelset - front and rear together, not a single wheel.
Fit and compatibility
The Wanderer Carbon System is a 29in wheel. The front hub comes in 15x110 Boost or 15x110 with RockShox Torque Caps. Rear options are unusually broad: 10x135 quick release, 12x135, 12x142 single speed, and 12x148 Boost.
Driver bodies are Shimano HG, Shimano Micro Spline, SRAM XD, and Single Speed; a front wheel ordered alone takes None (front wheel only). The hub is 6-bolt. Bikepacking frames span a lot of standards, so we confirm your dropouts and drivetrain before Industry Nine builds the wheel.
How Industry Nine tests its wheels
Industry Nine has anodized and machined hubs, spokes, and drive systems in Asheville, North Carolina since 2004. The company grew out of a family machine shop in the Blue Ridge and states that it engineers and manufactures every component of its hub and wheel systems in-house, including hub shells, axles, spokes, pawls, drive rings, and anodizing. Complete wheels are hand built to order and ship in approximately two weeks, fulfilled from Asheville, Kamloops, or Cadiz depending on location and inventory. In 2025 Industry Nine acquired We Are One Composites, which now operates as WR1, its carbon rim design program and manufacturer; WR1 has hand laid carbon rims under one roof in Kamloops, British Columbia since 2017.
Three hub platforms cover the range. Hydra2, the flagship mountain hub, was developed from feedback on more than 100,000 first-generation Hydra hubs and pairs a reinforced 145-tooth steel drive ring with six phased oversized pawl pockets for 870 points of engagement at 0.41 degrees. Industry Nine cites a 65 percent thicker axle, 5.5mm pawl pockets with 26 percent better force dissipation, 60 percent less coasting drag than the original Hydra, 6903 hub shell bearings, and full-contact radial lip seals with a labyrinth channel; it is rated for trail, enduro, downhill, e-bike, bikepacking, and dirt jump use. Solix, the gravel, road, and cross-country hub, uses a patented continuously phased freehub in which five pawls and a 121-tooth drive ring produce 605 points of engagement at 0.59 degrees. Its pawls and drive rings are cut from A2 tool steel by wire EDM, bearing spec is equalized front and rear, end caps carry full-contact seals behind a proximity dust and water shield, and preload is set by bore-diameter contraction. The 1/1 hub is the entry platform, with a dual-phase pawl drive giving 90 points of engagement at 4 degrees, high-capacity bearings, and a conventional flanged shell for J-bend Sapim steel spokes. Hydra2 and Solix are offered as System hubs, which take Industry Nine's direct-thread machined aluminum spokes, or as Classic hubs with scalloped flanges for J-bend steel spokes.
Convergence is the carbon rim technology shared by the Whisp, Sector, Triad, Deal, Fuse, Wanderer, and Revive 2.0 rims. Industry Nine says the program ran through 208 versions over two years before release. The rim's alternating spoke bed faces are angled at 7.5 degrees so that each nipple bed aligns with the hub flange, producing a linear spoke line and 360 degree contact between nipple and rim; articulation is listed as plus or minus 7.5 degrees for mountain rims and plus or minus 6 degrees for gravel and bikepacking rims, with a 4.3mm spoke hole. A ZRT composite film from Boston Materials, containing 13 billion Z-axis carbon fibers per square meter, is built into the spoke bed, and Industry Nine reports the rim is 32 percent stronger than its predecessor with tuned vertical compliance. Every Convergence rim is laid up by a named technician, assigned a serial number, and shipped without sanding, filling, or painting. On the road side, the R35, R50, and R65 carbon rims are described as CFD born and wind tunnel tested and among the fastest disc-specific rims available. Industry Nine characterizes its validation as in-house pressure testing in the same environments its riders use rather than published laboratory figures, and it does not list a rider weight limit on current product pages.
Warranty coverage is administered from Asheville for the United States and Canada. All Hydra2 and Solix hubs carry a Five-Year Limited Hub Warranty regardless of purchase date; for other products the current terms apply to purchases made on or after January 1, 2026. Hubs are covered against defects in materials and workmanship for five years, with parts, labor, and return shipping included in the first two years and parts only in years three through five; bearings and other wear items are excluded. Carbon rims are covered for the life of the original owner against defects and also against impact damage sustained while riding within the wheel's intended use, with a rim replacement or a factory rebuild offered when a claim qualifies. Alloy rims are covered for life against manufacturing defects, including split seams and cracks at spoke holes, with full parts, labor, and return shipping for the first two years; impact or crash damage on alloy rims is not a warranty item but may qualify for the Crash Replacement program. Aluminum System spokes are covered for confirmed manufacturing defects. Coverage applies to the original purchaser with proof of purchase from a certified Industry Nine dealer or distributor, and claims are filed through the Service and Warranty Request form on the company's website. Industry Nine also offers factory service on all products and states that no proprietary tools are required for routine hub service.
Industry Nine's videos
From Industry Nine
Warranty and certifications
- Five-Year Limited Hub Warranty — All Hydra2 and Solix hubs are covered for five years against defects in materials and workmanship regardless of purchase date; parts, labor, and return shipping in years one and two, parts only in years three through five; bearings and wear items excluded (source)
- Lifetime carbon rim warranty including riding impact — Convergence and R-series carbon rims are covered for the life of the original owner against defects and against impact damage sustained while riding within the wheel's intended use; rim replacement or factory rebuild offered on qualifying claims (source)
- Lifetime alloy rim defect coverage and Crash Replacement — Aluminum rims are covered for life against manufacturing defects such as split seams and spoke-hole cracks, with full parts, labor, and return shipping for the first two years; crash and impact damage is handled under the Crash Replacement program (source)
- CFD and wind tunnel validated R-series rims — The R35, R50, and R65 carbon road rims are described by Industry Nine as CFD born and wind tunnel tested and among the fastest disc-specific rims available (source)
- ZRT-reinforced Convergence spoke bed, 32 percent stronger — Boston Materials ZRT composite film with 13 billion Z-axis carbon fibers per square meter is built into the spoke bed; Industry Nine reports a 32 percent strength gain over the previous generation, with every rim hand laid by a named technician in Kamloops and serial numbered (source)
- Patented continuously phased freehub — Five pawls on a 121-tooth drive ring give the Solix hub 605 points of engagement at 0.59 degrees; Hydra2 uses six pawls and a 145-tooth ring for 870 points at 0.41 degrees; pawls and drive rings are wire-EDM cut from A2 tool steel (source)
Sources on Industry Nine's site:
- Industry Nine Warranty and Rider Support
- Choose Your Hub: Hydra2, SOLiX, and 1/1 platforms
- WR1 Convergence Carbon rim technology
- About Industry Nine: Two Brands, One Standard
- Industry Nine Solix Hubs
- Solix service documents and exploded views
The figures, certificates and media above are Industry Nine's own. ProWheelBuilder does not run these tests; we sell the wheel and stand behind the order.
A note on Industry Nine
Convergence is the name Industry Nine gives its carbon rim platform, and the models are not one rim in different widths: each gets its own layup, tuned for what that wheel is asked to do. It is why a Sector and a Triad can share a factory and a philosophy and still ride nothing like each other.
Ordering it from ProWheelBuilder
ProWheelBuilder sells the Wanderer Carbon System wheelset as an authorized Industry Nine dealer in Georgia. Industry Nine builds it to your colors and axle standards in Asheville, North Carolina and ships in about two weeks. We are not the manufacturer; we take the order, check the axle and driver picks against your frame, and support the wheel afterward.
If you want a Hydra2 System hub on a different rim, a dynamo front, or a steel-spoke build for remote repairs, our Custom Wheel program builds custom wheels on Industry Nine hubs in our shop.
Warranty
Industry Nine's warranty. Industry Nine covers its hubs against defects in materials and workmanship for five years from purchase, with two years on the anodized finish. Its alloy and carbon rims carry a lifetime defect warranty to the original purchaser, with parts, labor and return shipping covered for the first two years and parts thereafter. Bearing wear, impact and crash damage are not defects.
ProWheelBuilder. This is a complete wheelset built by its manufacturer rather than in our shop, so the maker's warranty above is the one that applies to it. ProWheelBuilder's own one-year wheel warranty covers the wheels we build. We will still handle a manufacturer claim on your behalf.
Full terms are on our Policies & Warranty page.
Wanderer Carbon SYSTEM questions
Is ProWheelBuilder the manufacturer of the Wanderer Carbon System?
No. Industry Nine builds it in Asheville, North Carolina, with Convergence carbon rims made by We Are One in Kamloops. ProWheelBuilder is a reseller and custom wheel builder in Georgia.
What does the 2mm offset do?
It shifts the spoke bed toward the non-drive side so the rear wheel's spoke tensions are more even, which improves strength and durability under load.
Can I run it single speed?
Yes. A Single Speed driver and a 12x142 single-speed rear axle are offered.
Does it fit an older 135mm frame?
Yes. 10x135 quick release and 12x135 rear options are available.
What tires suit the 27mm inner width?
2.1 to 2.4in bikepacking and trail tires.
Should I carry spare spokes?
Yes. System spokes are Industry Nine parts, so carry one front and one rear length on remote trips.
Not sure? Text or leave a voicemail on 470-253-0929 or email info@prowheelbuilder.com — you will be talking to the people who build wheels for a living.
