There are no products listed under this category.
Ibis Wheels with Paul Hubs
Custom Ibis Wheels on Paul Hubs
Pick an Ibis rim we carry, put it on a Paul hub, and we lace and true the wheel by hand in our Georgia shop.
Why build Ibis rims on Paul hubs:
- Made by specialists: Paul hubs machined in Chico, California
- Proven: Ibis builds a hollow box-section bead wall to stop pinch flats; Paul made the first purpose-built single speed mountain bike hub in 1996
- Built to last: Paul's sealed bearings are user adjustable; Ibis gives the original owner a lifetime warranty on its rims
- Laced and trued by hand, one wheel at a time, in our Georgia shop
- In depth below: Blackbird Send 2 mountain
Build your custom Ibis wheel on Paul hubs for:
Or start from the Paul hub you want:
Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Ibis rim and Paul hub already chosen.
Mountain in depth
Ibis Blackbird Send 2 wheels on Paul FHub Disc hubs
Our mountain pick from the Ibis and Paul parts we build with. The Ibis Blackbird Send 2 is a hooked aluminum rim, 35mm inside, 17mm deep, about 625 grams in 29 inch, sized for about 2.4 to 2.8 inch tires. We lace it to Paul FHub Disc hubs (front wheel) in 32 hole.
- Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
- The hub that started single speed mountain bikes. Paul introduced the Wacky One-Speed Rear Device in 1996 and calls it the first purpose-built single speed mountain bike hub. Paul says its 52mm chainline is a standard that continues today.
Start building this pair:
Mountain Bike
Ibis rims on Paul hubs for mountain bikes
Each card opens our custom wheel builder with the rim and hub for a front wheel already picked, on the Paul hub our customers choose most with that rim. The builder offers every Paul hub that fits, and you choose the colors, spokes and the rest.
More about Ibis and Paul wheels
Why the pairing, specs and FAQ
Custom hand built Ibis wheels on Paul hubs
Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.
What Ibis rims and Paul hubs each bring
- A hollow box-section bead wall. Pinch flats happen when a hard hit traps the tire against the rim edge. Ibis removes the sharp edge with a hollow box-section bead wall that gives the tire a broad contact point, and it says the wall is stronger with no added weight.
- Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
- A front and rear pairing. The rear wheel takes the brunt of the damage, so Ibis's own wheelsets put a Send 1 up front and a Send 2 in back.
- The hub that started single speed mountain bikes. Paul introduced the Wacky One-Speed Rear Device in 1996 and calls it the first purpose-built single speed mountain bike hub. Paul says its 52mm chainline is a standard that continues today.
- A rear wheel with no dish. On the WORD, Paul spread the flanges as far as it could while leaving room for freewheel threads. Both sides of the wheel can then be built alike, which Paul says makes a strong dishless wheel.
- An axle that runs from dropout to dropout. The disc hubs use an interchangeable 7075 aluminum axle in quick release, bolt-on or thru axle form, not end caps that can fall off when the wheel comes out. Change forks later and you change the axle, not the hub.
Ibis and Paul custom wheel questions
Which Paul hub fits my Ibis rim?
The cards on this page start on the Paul hub our customers build with each rim most often (Paul FHub Disc). The builder lists every Paul hub that fits your rim, in the drillings and brake types that match.
Do you build Ibis rims on other hubs?
Yes. See our Ibis custom wheel page for every hub that fits each Ibis rim, or our Paul custom wheel page for every rim on a Paul hub.
Can you build with a Paul hub or Ibis rim I already own?
Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.
How long will my wheel take?
Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.
Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.
Not sure which rim or hub?
Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.
Open the Build Assistant →