Skip to main content

Teravail Wheels with Chris King Hubs

The ProWheelBuilder workshop

Custom Teravail Wheels on Chris King Hubs

Pick a Teravail rim we carry, put it on a Chris King hub, and we lace and true the wheel by hand in our Georgia shop.

Why build Teravail rims on Chris King hubs:

  • Made by specialists: Chris King hubs engineered, made and assembled in Portland, Oregon
  • Proven: Teravail tests its Fluent mountain rim to ASTM category 3, for trail and all-mountain riding; Chris King rates its RingDrive above 800 foot-pounds of torque
  • Built to last: Chris King makes its own bearings, which it says get faster with age; Teravail backs its rims with a lifetime warranty for the original owner
  • Laced and trued by hand, one wheel at a time, in our Georgia shop
  • In depth below: Circos Carbon gravel · Fluent Carbon mountain
Read more

Build your custom Teravail wheel on Chris King hubs for:

Or start from a specific Chris King hub (3)

Or pick one of the 3 ready-made pairs below: each opens our custom wheel builder with the Teravail rim and Chris King hub already chosen.

Where to start

The Teravail and Chris King builds our customers choose most

Gravel

Teravail Circos Carbon wheels on Chris King R45 Disc hubs

Our gravel pick from the Teravail and Chris King parts we build with. The Teravail Circos Carbon is a hookless carbon rim, 25mm inside, 30mm deep, about 365 grams in 700c, sized for about 35 to 50mm tires.

Specs and why it works

We lace it to Chris King R45 Disc hubs in 24 hole.

  • Rims designed around the tires. Teravail started as a tire brand and designed its rims to pair with its own tires, so tire installation, tubeless setup and ride feel stay consistent. It recommends its own tubeless tape: one layer 27mm wide on the Circos, one layer 33mm wide on the Fluent, two layers 33mm wide on the Circos Wide 32.
  • Service without special tools. Take out the snap ring and seal, clean and regrease, and the bearing is ready to go again. A complete rebuild uses Chris King's own hub service tools.

Mountain

Teravail Fluent Carbon wheels on Chris King MTB 6-bolt hubs

Our mountain pick from the Teravail and Chris King parts we build with. The Teravail Fluent Carbon is a hookless carbon rim, 30mm inside, 25mm deep, about 450 grams in 29 inch, sized for about 2.3 to 2.6 inch tires.

Specs and why it works

We lace it to Chris King MTB 6-bolt hubs in 32 hole.

  • Reinforced and tested. Teravail reinforces the spoke bed and requires nipple washers in its rims, so we build every Teravail wheel with them. Teravail tests the Fluent to ASTM category 3, the class for trail and all-mountain riding, and says it tested the Circos Wide 32 beyond that.
  • Every tooth engages at once. Two heat-treated stainless steel rings mesh at 72 points on mountain hubs and 45 on the R45, all at the same moment. Chris King rates the system above 800 foot-pounds of torque and says that is three times the other high-end hubs it tested.

Questions about these builds

Which Teravail rim should I build on Chris King hubs?

For gravel, the Circos Carbon (25mm inside) on Chris King R45 Disc hubs; for mountain, the Fluent Carbon (30mm inside) on Chris King MTB 6-bolt hubs. Each one opens the builder from its section above, and the cards below cover every Teravail rim that fits a Chris King hub.

Road / Cross / Gravel

Teravail rims on Chris King hubs for road, cross and gravel bikes

Each card opens our custom wheel builder with the rims and hubs for a wheelset already picked, on the Chris King hub our customers choose most with that rim. The builder offers every Chris King hub that fits, and you choose the colors, spokes and the rest.

Mountain Bike

Teravail rims on Chris King hubs for mountain bikes

Each card opens our custom wheel builder with the rims and hubs for a wheelset already picked, on the Chris King hub our customers choose most with that rim. The builder offers every Chris King hub that fits, and you choose the colors, spokes and the rest.

More about Teravail and Chris King wheels

Why the pairing, specs and FAQ

Custom hand built Teravail wheels on Chris King hubs

Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.

What Teravail rims and Chris King hubs each bring

  • Rims designed around the tires. Teravail started as a tire brand and designed its rims to pair with its own tires, so tire installation, tubeless setup and ride feel stay consistent. It recommends its own tubeless tape: one layer 27mm wide on the Circos, one layer 33mm wide on the Fluent, two layers 33mm wide on the Circos Wide 32.
  • Front and rear drilled differently. Every Teravail rim comes in front-specific and rear-specific versions; the Circos Wide 32 even differs in width, 29mm inside at the front and 28mm at the rear. Teravail sets the drilling of each for better spoke bracing angles, so load passes smoothly from the rim through the nipples and spokes to the hub.
  • A thick hookless flange. Teravail gave the Circos a shallow profile with thick hookless flanges to keep the weight down and let the rim absorb and deflect around impacts. The Fluent's flange is extra thick for singletrack.
  • RingDrive sits inside the shell. Chris King moved the engagement mechanism inboard of the large hub shell bearing. It says that gives more contact area than a traditional freehub and handles drivetrain torque better.
  • Every tooth engages at once. Two heat-treated stainless steel rings mesh at 72 points on mountain hubs and 45 on the R45, all at the same moment. Chris King rates the system above 800 foot-pounds of torque and says that is three times the other high-end hubs it tested.
  • Bearings it makes itself. Chris King designs and builds its own sealed angular-contact bearings, and each one is inspected and assembled by hand. Unlike a common radial bearing they can be adjusted in use, and Chris King says they wear in rather than wear out.

Check before you order

  • Tires. Every Teravail rim on this page is hookless, so choose a tire its maker rates for hookless rims.

Teravail and Chris King custom wheel questions

Which Chris King hub fits my Teravail rim?

The cards on this page start on the Chris King hub our customers build with each rim most often (Chris King R45 Disc, Chris King MTB 6-bolt). The builder lists every Chris King hub that fits your rim, in the drillings and brake types that match.

Do you build Teravail rims on other hubs?

Yes. See our Teravail custom wheel page for every hub that fits each Teravail rim, or our Chris King custom wheel page for every rim on a Chris King hub.

Can you build with a Chris King hub or Teravail rim I already own?

Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.

How long will my wheel take?

Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.

Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.

Not sure which rim or hub?

Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.

Open the Build Assistant →

There are no products listed under this category.