Skip to main content

Chromag Wheels with Chris King Hubs

The ProWheelBuilder workshop

Custom Chromag Wheels on Chris King Hubs

Pick a Chromag rim we carry, put it on a Chris King hub, and we lace and true the wheel by hand in our Georgia shop.

Why build Chromag rims on Chris King hubs:

  • Made by specialists: Chris King hubs engineered, made and assembled in Portland, Oregon
  • Proven: Chromag says the BA30 v2 takes 20 percent more impact than the original at the same weight; Chris King rates its RingDrive above 800 foot-pounds of torque
  • Built to last: Chris King makes its own bearings, which it says get faster with age; Chromag welds and grinds the seam so the joint is the strongest part of the rim
  • Laced and trued by hand, one wheel at a time, in our Georgia shop
  • In depth below: BA30 V2 mountain
Read more

Build your custom Chromag wheel on Chris King hubs for:

Or start from a specific Chris King hub (3)

Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Chromag rim and Chris King hub already chosen.

Where to start

The Chromag and Chris King builds our customers choose most

Mountain

Chromag BA30 V2 wheels on Chris King MTB 6-bolt hubs

Our mountain pick from the Chromag and Chris King parts we build with. The Chromag BA30 V2 is a hooked aluminum rim, 30mm inside, 19mm deep, about 640 grams in 29 inch, sized for about 2.3 to 2.6 inch tires.

Specs and why it works

We lace it to Chris King MTB 6-bolt hubs in 32 hole.

  • A bead wall built for rock strikes. Chromag concentrates material in the bead wall, where impacts land, and rounds the outer edge to reduce tire damage under compression. The aim is better dent resistance and tire retention, and fewer pinch flats.
  • Every tooth engages at once. Two heat-treated stainless steel rings mesh at 72 points on mountain hubs and 45 on the R45, all at the same moment. Chris King rates the system above 800 foot-pounds of torque and says that is three times the other high-end hubs it tested.

Mountain Bike

Chromag rims on Chris King hubs for mountain bikes

Each card opens our custom wheel builder with the rims and hubs for a wheelset already picked, on the Chris King hub our customers choose most with that rim. The builder offers every Chris King hub that fits, and you choose the colors, spokes and the rest.

More about Chromag and Chris King wheels

Why the pairing, specs and FAQ

Custom hand built Chromag wheels on Chris King hubs

Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.

What Chromag rims and Chris King hubs each bring

  • A bead wall built for rock strikes. Chromag concentrates material in the bead wall, where impacts land, and rounds the outer edge to reduce tire damage under compression. The aim is better dent resistance and tire retention, and fewer pinch flats.
  • A welded and ground seam. Both rims are fusion welded at the joint and then ground smooth, and Chromag says that makes the seam the strongest part of the rim. A full weld also keeps the joint airtight for tubeless.
  • Nipple beds angled to the spoke. Chromag's oriented bed lines up each nipple seat with the angle of its spoke. Chromag says this reduces stress on the nipple and spoke, which makes for a stronger wheel.
  • RingDrive sits inside the shell. Chris King moved the engagement mechanism inboard of the large hub shell bearing. It says that gives more contact area than a traditional freehub and handles drivetrain torque better.
  • Every tooth engages at once. Two heat-treated stainless steel rings mesh at 72 points on mountain hubs and 45 on the R45, all at the same moment. Chris King rates the system above 800 foot-pounds of torque and says that is three times the other high-end hubs it tested.
  • Bearings it makes itself. Chris King designs and builds its own sealed angular-contact bearings, and each one is inspected and assembled by hand. Unlike a common radial bearing they can be adjusted in use, and Chris King says they wear in rather than wear out.

Chromag and Chris King custom wheel questions

Which Chris King hub fits my Chromag rim?

The cards on this page start on the Chris King hub our customers build with each rim most often (Chris King MTB 6-bolt). The builder lists every Chris King hub that fits your rim, in the drillings and brake types that match.

Do you build Chromag rims on other hubs?

Yes. See our Chromag custom wheel page for every hub that fits each Chromag rim, or our Chris King custom wheel page for every rim on a Chris King hub.

Can you build with a Chris King hub or Chromag rim I already own?

Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.

How long will my wheel take?

Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.

Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.

Not sure which rim or hub?

Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.

Open the Build Assistant →

There are no products listed under this category.