There are no products listed under this category.
Ibis Wheels with Boyd Hubs
Custom Ibis Wheels on Boyd Hubs
Pick an Ibis rim we carry, put it on a Boyd hub, and we lace and true the wheel by hand in our Georgia shop.
Why build Ibis rims on Boyd hubs:
- Proven: Ibis builds a hollow box-section bead wall to stop pinch flats; Boyd's 36-tooth hubs engage every 5 degrees
- Built to last: Boyd hubs change freehubs by hand and spin on Enduro ABEC-5 bearings; Ibis gives the original owner a lifetime warranty on its rims
- Laced and trued by hand, one wheel at a time, in our Georgia shop
- In depth below: Blackbird Send 2 mountain
Build your custom Ibis wheel on Boyd hubs for:
Or start from the Boyd hub you want:
Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Ibis rim and Boyd hub already chosen.
Mountain in depth
Ibis Blackbird Send 2 wheels on Boyd Quest hubs
Our mountain pick from the Ibis and Boyd parts we build with. The Ibis Blackbird Send 2 is a hooked aluminum rim, 35mm inside, 17mm deep, about 625 grams in 29 inch, sized for about 2.4 to 2.8 inch tires. We lace it to Boyd Quest hubs (rear wheel) in 32 hole.
- Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
- Five degrees of engagement. The 85 Road and the Quest both turn on 36 teeth and engage every 5 degrees. That cuts the dead spot before the drive catches when you start pedaling again, such as coming out of a corner.
Start building this pair:
Mountain Bike
Ibis rims on Boyd hubs for mountain bikes
Each card opens our custom wheel builder with the rim and hub for a rear wheel already picked, on the Boyd hub our customers choose most with that rim. The builder offers every Boyd hub that fits, and you choose the colors, spokes and the rest.
More about Ibis and Boyd wheels
Why the pairing, specs and FAQ
Custom hand built Ibis wheels on Boyd hubs
Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.
What Ibis rims and Boyd hubs each bring
- A hollow box-section bead wall. Pinch flats happen when a hard hit traps the tire against the rim edge. Ibis removes the sharp edge with a hollow box-section bead wall that gives the tire a broad contact point, and it says the wall is stronger with no added weight.
- Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
- A front and rear pairing. The rear wheel takes the brunt of the damage, so Ibis's own wheelsets put a Send 1 up front and a Send 2 in back.
- Five degrees of engagement. The 85 Road and the Quest both turn on 36 teeth and engage every 5 degrees. That cuts the dead spot before the drive catches when you start pedaling again, such as coming out of a corner.
- Three pawls at a time on the Quest. The Quest has six pawls working in two sets of three on its 36-tooth ring, so three pawls carry the load at each engagement.
- Tool-free changes. Quest end caps and freehub bodies swap by hand, and the 85 Road offers tool-free service with a swappable freehub. A new frame, axle standard or groupset does not have to mean a new hub.
Ibis and Boyd custom wheel questions
Which Boyd hub fits my Ibis rim?
The cards on this page start on the Boyd hub our customers build with each rim most often (Boyd Quest). The builder lists every Boyd hub that fits your rim, in the drillings and brake types that match.
Do you build Ibis rims on other hubs?
Yes. See our Ibis custom wheel page for every hub that fits each Ibis rim, or our Boyd custom wheel page for every rim on a Boyd hub.
Can you build with a Boyd hub or Ibis rim I already own?
Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.
How long will my wheel take?
Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.
Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.
Not sure which rim or hub?
Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.
Open the Build Assistant →