Skip to main content

Ibis Wheels with Industry Nine Hubs

The ProWheelBuilder workshop

Custom Ibis Wheels on Industry Nine Hubs

Pick an Ibis rim we carry, put it on an Industry Nine hub, and we lace and true the wheel by hand in our Georgia shop.

Why build Ibis rims on Industry Nine hubs:

  • Made by specialists: Industry Nine hubs machined and anodized in Asheville, North Carolina
  • Proven: Ibis builds a hollow box-section bead wall to stop pinch flats; Industry Nine built the Hydra2 from feedback on over 100,000 ridden hubs
  • Built to last: Industry Nine's classic hubs take standard J-bend spokes and service without proprietary tools; Ibis gives the original owner a lifetime warranty on its rims
  • More than 20 Ibis wheels on Industry Nine hubs in our build records since 2009
  • In depth below: Ibis Blackbird Send trail
Read more

Build your custom Ibis wheel on Industry Nine hubs for:

Or start from a specific Industry Nine hub (5)

Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Ibis rim and Industry Nine hub already chosen.

Where to start

The Ibis and Industry Nine builds our customers choose most

Trail

Ibis Blackbird Send wheels on Industry Nine 1/1 MTB hubs

The Ibis and Industry Nine pair our customers build most from the parts we carry now, with 2 in our build records on the Send 2. Ibis's alloy trail rims are 35mm inside and 17mm deep for 2.4 to 2.6 inch tires, with hollow box bead walls that protect the tire from pinch flats and sidewall cuts and a Stan's BST tubeless bead.

Specs and why it works

The Send 2 is the rear-specific one, reinforced under the bead seat, about 625 grams in 29 inch, meant to be built behind a Send 1 front as a matched pair.

  • 90 points, sealed for mud. The 1/1 MTB rear runs a dual-phased six-pawl driver on a 45-tooth ring, four degrees of pickup, behind labyrinth radial lip seals, with HG, XD and Micro Spline freehubs that swap without tools.
  • Ribs under the bead seat. A dented bead wall can be bent back, but a dented bead seat cannot, and then the tire will not seal tubeless; the Send 2 adds a pair of ribs beneath the seat for about 45 grams.
  • Or the Hydra 2. Industry Nine's 870-point hub, 0.41 degrees of pickup, under the same rims.

Questions about these builds

Why a Send 1 front and a Send 2 rear?

Both are 35mm inside and 17mm deep. The Send 2 adds ribs under the bead seat for what a rear wheel takes; the Send 1 front is about 60 grams lighter.

1/1 or Hydra 2?

The 1/1 MTB engages in four degrees, with 90 points, from a dual-phased six-pawl driver. The Hydra 2 engages in 0.41 degrees, with 870 points.

Mountain Bike

Ibis rims on Industry Nine hubs for mountain bikes

Each card opens our custom wheel builder with the rims and hubs for a wheelset already picked, on the Industry Nine hub our customers choose most with that rim. The builder offers every Industry Nine hub that fits, and you choose the colors, spokes and the rest.

More about Ibis and Industry Nine wheels

Why the pairing, specs and FAQ

Custom hand built Ibis wheels on Industry Nine hubs

Our order records show more than 20 Ibis wheels laced to Industry Nine hubs since 2009. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.

What Ibis rims and Industry Nine hubs each bring

  • A hollow box-section bead wall. Pinch flats happen when a hard hit traps the tire against the rim edge. Ibis removes the sharp edge with a hollow box-section bead wall that gives the tire a broad contact point, and it says the wall is stronger with no added weight.
  • Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
  • A front and rear pairing. The rear wheel takes the brunt of the damage, so Ibis's own wheelsets put a Send 1 up front and a Send 2 in back.
  • Hydra2 reinforced from real use. Industry Nine says feedback from over 100,000 ridden Hydra hubs showed it where to push further. The result is an axle 65 percent thicker, larger bearings and a full-contact seal system.
  • Stronger parts around the pawls. Each pawl gains a tooth, for three in all, and the drive ring moves to a more fatigue-resistant steel. Deeper 5.5mm pawl pockets spread force 26 percent better, which Industry Nine says stops them deforming and lets the hub handle powerful e-bike motors.
  • SOLiX and continuous phasing. Five pawls work against a 121-tooth drive ring for 605 points of engagement, or 0.59 degrees. Industry Nine says power arrives at once and then loads progressively, in a light hub for cross-country, gravel and road.

Ibis and Industry Nine custom wheel questions

Which Industry Nine hub fits my Ibis rim?

The cards on this page start on the Industry Nine hub our customers build with each rim most often (Industry Nine 1/1 MTB Centerlock). The builder lists every Industry Nine hub that fits your rim, in the drillings and brake types that match.

Do you build Ibis rims on other hubs?

Yes. See our Ibis custom wheel page for every hub that fits each Ibis rim, or our Industry Nine custom wheel page for every rim on an Industry Nine hub.

Can you build with an Industry Nine hub or Ibis rim I already own?

Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.

How long will my wheel take?

Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.

Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.

Not sure which rim or hub?

Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.

Open the Build Assistant →

There are no products listed under this category.