There are no products listed under this category.
Ibis Wheels with SON Hubs
Custom Ibis Wheels on SON Hubs
Pick an Ibis rim we carry, put it on a SON hub, and we lace and true the wheel by hand in our Georgia shop.
Why build Ibis rims on SON hubs:
- Made by specialists: SON hubs made in Tuebingen, Germany
- Proven: Ibis builds a hollow box-section bead wall to stop pinch flats; SON hubs run many tens of thousands of kilometers with no adjustment
- Built to last: SON backs every hub with a five-year warranty; Ibis gives the original owner a lifetime warranty on its rims
- Laced and trued by hand, one wheel at a time, in our Georgia shop
- In depth below: Blackbird Send 2 mountain
Build your custom Ibis wheel on SON hubs for:
Or start from the SON hub you want:
28 Fat Bike 6-bolt, front only→28 Centerlock, front only→28 6-bolt, front only→Delux Centerlock, front only→
Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Ibis rim and SON hub already chosen.
Mountain in depth
Ibis Blackbird Send 2 wheels on SON 28 Disc 6-bolt hubs
Our mountain pick from the Ibis and SON parts we build with. The Ibis Blackbird Send 2 is a hooked aluminum rim, 35mm inside, 17mm deep, about 625 grams in 29 inch, sized for about 2.4 to 2.8 inch tires. We lace it to SON 28 Disc 6-bolt hubs (front wheel) in 32 hole.
- Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
- A generator tuned to how you ride. The SON 28 is SON's all-purpose choice, with strong output even at low speed, including for charging devices. The SONdelux is lighter with lower mechanical resistance for fast riders and small wheels, and it gives up some output below 20 km/h.
Start building this pair:
Mountain Bike
Ibis rims on SON hubs for mountain bikes
Each card opens our custom wheel builder with the rim and hub for a front wheel already picked, on the SON hub our customers choose most with that rim. The builder offers every SON hub that fits, and you choose the colors, spokes and the rest.
More about Ibis and SON wheels
Why the pairing, specs and FAQ
Custom hand built Ibis wheels on SON hubs
Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.
What Ibis rims and SON hubs each bring
- A hollow box-section bead wall. Pinch flats happen when a hard hit traps the tire against the rim edge. Ibis removes the sharp edge with a hollow box-section bead wall that gives the tire a broad contact point, and it says the wall is stronger with no added weight.
- Ribs under the bead seat on the Send 2. A dented bead wall can be bent back, but Ibis says a dented bead seat can't, and then the tire will not seal tubeless. The Send 2 adds a pair of ribs right beneath the seat to prevent that, for about 45 grams per rim.
- A front and rear pairing. The rear wheel takes the brunt of the damage, so Ibis's own wheelsets put a Send 1 up front and a Send 2 in back.
- A generator with its coil in the center. SON uses a claw-pole generator with the coil placed centrally and carefully made sheet metal parts, which it says keeps losses low when the lights are off. It works without gears or contact, so SON says the generator itself does not wear.
- Pressure compensation to keep water out. SON credits this system, which ends in the axle bore, for its protection against water getting in. It is why SON asks you not to grease the skewer shaft and to keep strong jets of water off the hub.
- Bearings that need nothing from you. SON uses SKF ball bearings sealed on both sides and lubricated for life, which it says run many tens of thousands of kilometers with no adjustment. All SON hubs carry a five-year warranty.
Ibis and SON custom wheel questions
Which SON hub fits my Ibis rim?
The cards on this page start on the SON hub our customers build with each rim most often (SON 28 Disc 6-bolt). The builder lists every SON hub that fits your rim, in the drillings and brake types that match.
Do you build Ibis rims on other hubs?
Yes. See our Ibis custom wheel page for every hub that fits each Ibis rim, or our SON custom wheel page for every rim on a SON hub.
Can you build with a SON hub or Ibis rim I already own?
Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.
How long will my wheel take?
Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.
Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.
Not sure which rim or hub?
Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.
Open the Build Assistant →