There are no products listed under this category.
Stan's NoTubes Wheels with Industry Nine Hubs
Custom Stan's NoTubes Wheels on Industry Nine Hubs
Pick a Stan's NoTubes rim we carry, put it on an Industry Nine hub, and we lace and true the wheel by hand in our Georgia shop.
Why build Stan's NoTubes rims on Industry Nine hubs:
- Made by specialists: Industry Nine hubs machined and anodized in Asheville, North Carolina
- Proven: Stan's patented Bead Socket rims helped make tubeless mountain biking mainstream; Industry Nine built the Hydra2 from feedback on over 100,000 ridden hubs
- Built to last: Industry Nine's classic hubs take standard J-bend spokes and service without proprietary tools
- More than 130 Stan's NoTubes wheels on Industry Nine hubs in our build records since 2009, each laced and trued by hand in Georgia
- In depth below: Arch MK4 mountain
Build your custom Stan's NoTubes wheel on Industry Nine hubs for:
Or start from the Industry Nine hub you want:
Hydra2 MTB Centerlock→Hydra2 MTB 6-bolt→1/1 MTB Centerlock→1/1 MTB 6-bolt→1/1 Road Centerlock→SOLiX CL→Hydra2 Single Speed 6-bolt, rear only→
Or pick one of the 4 ready-made pairs below: each opens our custom wheel builder with the Stan's NoTubes rim and Industry Nine hub already chosen.
Mountain in depth
Stan's NoTubes Arch MK4 wheels on Industry Nine Hydra 2 MTB Centerlock hubs
Our mountain pick from the Stan's NoTubes and Industry Nine parts we build with. The Stan's NoTubes Arch MK4 is a hooked aluminum rim, 28mm inside, 18.9mm deep, about 481 grams in 29 inch, sized for about 2.3 to 2.6 inch tires. We lace it to Industry Nine Hydra 2 MTB Centerlock hubs in 32 hole.
- WideRight widths. A rim that is too narrow pinches the tire and one that is too wide distorts it, so Stan's sets widths to let the tire reach its intended shape. The 28mm Arch MK4, for example, is sized for 2.2 to 2.5 inch tires.
- Hydra2 reinforced from real use. Industry Nine says feedback from over 100,000 ridden Hydra hubs showed it where to push further. The result is an axle 65 percent thicker, larger bearings and a full-contact seal system.
Start building this pair:
Mountain Bike
Stan's NoTubes rims on Industry Nine hubs for mountain bikes
Each card opens our custom wheel builder with the rims and hubs for a wheelset already picked, on the Industry Nine hub our customers choose most with that rim. The builder offers every Industry Nine hub that fits, and you choose the colors, spokes and the rest.
Stan's NoTubes Flow EX3 on Industry Nine Hydra 2 MTB Centerlock29mm inside · 17.9mm deep · 32 hole · hookedStart building this pair →
Stan's NoTubes Arch MK4 on Industry Nine Hydra 2 MTB Centerlock28mm inside · 18.9mm deep · 32 hole · hookedStart building this pair →
Stan's NoTubes Crest MK4 on Industry Nine Hydra 2 MTB Centerlock25mm inside · 18mm deep · 32 hole · hookedStart building this pair →
Stan's NoTubes Flow MK4 on Industry Nine Hydra 2 MTB Centerlock30mm inside · 18.9mm deep · 32 hole · hookedStart building this pair →From our truing stand
Stan's NoTubes wheels on Industry Nine hubs we’ve built
Wheels we have built with Stan's NoTubes rims and Industry Nine hubs.
More about Stan's NoTubes and Industry Nine wheels
Why the pairing, specs and FAQ
Custom hand built Stan's NoTubes wheels on Industry Nine hubs
Our order records show more than 130 Stan's NoTubes wheels laced to Industry Nine hubs since 2009. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.
What Stan's NoTubes rims and Industry Nine hubs each bring
- Bead Socket Technology. Stan's patented rim shape holds the tire by its bead rather than its sidewall, so the sidewall can expand to a rounder profile. Stan's says that means more traction and less rolling resistance than a conventional shape, which drives the bead deeper and restricts tire volume.
- Low sidewalls. Bead Socket rims have lower sidewalls than conventional rims. Stan's says that leaves them less exposed, and makes the rim lighter and stronger.
- Spoke offset set by rim width. On MK4 rims the spoke holes sit 1.5mm off center on the 25mm Crest, 2.5mm on the 28mm Arch and 3mm on the 30mm Flow. Stan's reports 92 percent drive to non-drive tension balance on the Crest MK4, against 58 percent on the symmetric MK3.
- Hydra2 reinforced from real use. Industry Nine says feedback from over 100,000 ridden Hydra hubs showed it where to push further. The result is an axle 65 percent thicker, larger bearings and a full-contact seal system.
- Stronger parts around the pawls. Each pawl gains a tooth, for three in all, and the drive ring moves to a more fatigue-resistant steel. Deeper 5.5mm pawl pockets spread force 26 percent better, which Industry Nine says stops them deforming and lets the hub handle powerful e-bike motors.
- SOLiX and continuous phasing. Five pawls work against a 121-tooth drive ring for 605 points of engagement, or 0.59 degrees. Industry Nine says power arrives at once and then loads progressively, in a light hub for cross-country, gravel and road.
Stan's NoTubes and Industry Nine custom wheel questions
Which Industry Nine hub fits my Stan's NoTubes rim?
The cards on this page start on the Industry Nine hub our customers build with each rim most often (Industry Nine Hydra 2 MTB Centerlock). The builder lists every Industry Nine hub that fits your rim, in the drillings and brake types that match.
Do you build Stan's NoTubes rims on other hubs?
Yes. See our Stan's NoTubes custom wheel page for every hub that fits each Stan's NoTubes rim, or our Industry Nine custom wheel page for every rim on an Industry Nine hub.
Can you build with an Industry Nine hub or Stan's NoTubes rim I already own?
Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.
How long will my wheel take?
Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.
Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.
Not sure which rim or hub?
Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.
Open the Build Assistant →