Skip to main content

Chromag Wheels with DT Swiss Hubs

The ProWheelBuilder workshop

Custom Chromag Wheels on DT Swiss Hubs

Pick a Chromag rim we carry, put it on a DT Swiss hub, and we lace and true the wheel by hand in our Georgia shop.

Why build Chromag rims on DT Swiss hubs:

  • Made by specialists: DT Swiss hubs engineered in Biel, Switzerland
  • Proven: Chromag says the BA30 v2 takes 20 percent more impact than the original at the same weight; DT Swiss star ratchets engage every tooth at once instead of a few pawls
  • Built to last: DT Swiss freehubs come apart by hand, and the ratchets upgrade to more teeth later; Chromag welds and grinds the seam so the joint is the strongest part of the rim
  • Laced and trued by hand, one wheel at a time, in our Georgia shop
  • In depth below: BA30 V2 mountain
Read more

Build your custom Chromag wheel on DT Swiss hubs for:

Or start from a specific DT Swiss hub (5)

Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Chromag rim and DT Swiss hub already chosen.

Where to start

The Chromag and DT Swiss builds our customers choose most

Mountain

Chromag BA30 V2 wheels on DT Swiss 240 Disc Centerlock hubs

Our mountain pick from the Chromag and DT Swiss parts we build with. The Chromag BA30 V2 is a hooked aluminum rim, 30mm inside, 19mm deep, about 640 grams in 29 inch, sized for about 2.3 to 2.6 inch tires.

Specs and why it works

We lace it to DT Swiss 240 Disc Centerlock hubs in 32 hole.

  • A bead wall built for rock strikes. Chromag concentrates material in the bead wall, where impacts land, and rounds the outer edge to reduce tire damage under compression. The aim is better dent resistance and tire retention, and fewer pinch flats.
  • Ratchet EXP on the 240 and 180. One ratchet is combined with the threaded ring, leaving fewer parts and less weight. The drive-side bearing moves into that ring too, which widens the bearing spacing, and DT Swiss says this adds 15 percent axle stiffness and longer bearing life.

Mountain Bike

Chromag rims on DT Swiss hubs for mountain bikes

Each card opens our custom wheel builder with the rims and hubs for a wheelset already picked, on the DT Swiss hub our customers choose most with that rim. The builder offers every DT Swiss hub that fits, and you choose the colors, spokes and the rest.

More about Chromag and DT Swiss wheels

Why the pairing, specs and FAQ

Custom hand built Chromag wheels on DT Swiss hubs

Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.

What Chromag rims and DT Swiss hubs each bring

  • A bead wall built for rock strikes. Chromag concentrates material in the bead wall, where impacts land, and rounds the outer edge to reduce tire damage under compression. The aim is better dent resistance and tire retention, and fewer pinch flats.
  • A welded and ground seam. Both rims are fusion welded at the joint and then ground smooth, and Chromag says that makes the seam the strongest part of the rim. A full weld also keeps the joint airtight for tubeless.
  • Nipple beds angled to the spoke. Chromag's oriented bed lines up each nipple seat with the angle of its spoke. Chromag says this reduces stress on the nipple and spoke, which makes for a stronger wheel.
  • Star ratchets instead of pawls. Facing toothed rings take the drive, and all their teeth engage at the same moment. DT Swiss says a pawl has only a small contact area, while the whole face of its ratchet engages, and it credits the smaller point loads for these hubs' reliability.
  • Ratchet EXP on the 240 and 180. One ratchet is combined with the threaded ring, leaving fewer parts and less weight. The drive-side bearing moves into that ring too, which widens the bearing spacing, and DT Swiss says this adds 15 percent axle stiffness and longer bearing life.
  • The original Ratchet System on the 350. Two conical springs keep both ratchets aligned. DT Swiss calls it marginally heavier than Ratchet EXP, and the hub shell and axle on the current 350 have been reworked to cut weight.

Chromag and DT Swiss custom wheel questions

Which DT Swiss hub fits my Chromag rim?

The cards on this page start on the DT Swiss hub our customers build with each rim most often (DT Swiss 240 Disc Centerlock). The builder lists every DT Swiss hub that fits your rim, in the drillings and brake types that match.

Do you build Chromag rims on other hubs?

Yes. See our Chromag custom wheel page for every hub that fits each Chromag rim, or our DT Swiss custom wheel page for every rim on a DT Swiss hub.

Can you build with a DT Swiss hub or Chromag rim I already own?

Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.

How long will my wheel take?

Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.

Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.

Not sure which rim or hub?

Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.

Open the Build Assistant →

There are no products listed under this category.