Skip to main content

Chromag Wheels with SON Hubs

The ProWheelBuilder workshop

Custom Chromag Wheels on SON Hubs

Pick a Chromag rim we carry, put it on a SON hub, and we lace and true the wheel by hand in our Georgia shop.

Why build Chromag rims on SON hubs:

  • Made by specialists: SON hubs made in Tuebingen, Germany
  • Proven: Chromag says the BA30 v2 takes 20 percent more impact than the original at the same weight; SON hubs run many tens of thousands of kilometers with no adjustment
  • Built to last: SON backs every hub with a five-year warranty; Chromag welds and grinds the seam so the joint is the strongest part of the rim
  • Laced and trued by hand, one wheel at a time, in our Georgia shop
  • In depth below: BA30 V2 mountain
Read more

Build your custom Chromag wheel on SON hubs for:

Or start from a specific SON hub (4)

Or pick one of the 2 ready-made pairs below: each opens our custom wheel builder with the Chromag rim and SON hub already chosen.

Where to start

The Chromag and SON builds our customers choose most

Mountain

Chromag BA30 V2 wheels on SON 28 Disc 6-bolt hubs

Our mountain pick from the Chromag and SON parts we build with. The Chromag BA30 V2 is a hooked aluminum rim, 30mm inside, 19mm deep, about 640 grams in 29 inch, sized for about 2.3 to 2.6 inch tires.

Specs and why it works

We lace it to SON 28 Disc 6-bolt hubs (front wheel) in 32 hole.

  • A bead wall built for rock strikes. Chromag concentrates material in the bead wall, where impacts land, and rounds the outer edge to reduce tire damage under compression. The aim is better dent resistance and tire retention, and fewer pinch flats.
  • A generator tuned to how you ride. The SON 28 is SON's all-purpose choice, with strong output even at low speed, including for charging devices. The SONdelux is lighter with lower mechanical resistance for fast riders and small wheels, and it gives up some output below 20 km/h.

Mountain Bike

Chromag rims on SON hubs for mountain bikes

Each card opens our custom wheel builder with the rim and hub for a front wheel already picked, on the SON hub our customers choose most with that rim. The builder offers every SON hub that fits, and you choose the colors, spokes and the rest.

More about Chromag and SON wheels

Why the pairing, specs and FAQ

Custom hand built Chromag wheels on SON hubs

Every pair on this page is in our builder today, with a rim and hub that fit each other. We lace each wheel by hand in our Georgia shop: tensioned evenly, trued flat and round, and stress-relieved before it ships. Spoke lengths are calculated from the measured dimensions of your exact rim and hub.

What Chromag rims and SON hubs each bring

  • A bead wall built for rock strikes. Chromag concentrates material in the bead wall, where impacts land, and rounds the outer edge to reduce tire damage under compression. The aim is better dent resistance and tire retention, and fewer pinch flats.
  • A welded and ground seam. Both rims are fusion welded at the joint and then ground smooth, and Chromag says that makes the seam the strongest part of the rim. A full weld also keeps the joint airtight for tubeless.
  • Nipple beds angled to the spoke. Chromag's oriented bed lines up each nipple seat with the angle of its spoke. Chromag says this reduces stress on the nipple and spoke, which makes for a stronger wheel.
  • A generator with its coil in the center. SON uses a claw-pole generator with the coil placed centrally and carefully made sheet metal parts, which it says keeps losses low when the lights are off. It works without gears or contact, so SON says the generator itself does not wear.
  • Pressure compensation to keep water out. SON credits this system, which ends in the axle bore, for its protection against water getting in. It is why SON asks you not to grease the skewer shaft and to keep strong jets of water off the hub.
  • Bearings that need nothing from you. SON uses SKF ball bearings sealed on both sides and lubricated for life, which it says run many tens of thousands of kilometers with no adjustment. All SON hubs carry a five-year warranty.

Chromag and SON custom wheel questions

Which SON hub fits my Chromag rim?

The cards on this page start on the SON hub our customers build with each rim most often (SON 28 Disc 6-bolt). The builder lists every SON hub that fits your rim, in the drillings and brake types that match.

Do you build Chromag rims on other hubs?

Yes. See our Chromag custom wheel page for every hub that fits each Chromag rim, or our SON custom wheel page for every rim on a SON hub.

Can you build with a SON hub or Chromag rim I already own?

Yes. Choose the supply-your-own option in the configurator, ship it to us, and we will lace it into a new wheel with new spokes cut to the right length. You pay for the parts you need and the build labor.

How long will my wheel take?

Build time comes down to parts availability rather than bench time. Your estimated ship date is shown in the configurator before you check out, so you know the date before you pay.

Not sure what to pick? Email info@prowheelbuilder.com (fastest) or leave a voicemail on 470-253-0929. You will be talking to the people who build the wheels.

Not sure which rim or hub?

Tell the Build Assistant how you ride and what you want to spend, and it ranks complete builds for you.

Open the Build Assistant →

There are no products listed under this category.